通過式噴淋清洗機具有多工位，功能全，結構合理，操作方便，清洗效果好的優點，對于流水線零件的清洗，改善勞動環境，提高清洗質量有重要意義。其使用范圍較廣，適用于各種五金零件，壓鑄件，液壓件，齒輪，軸承，汽車零部件等各種制造業。

The through-type spray cleaning machine has the advantages of multiple stations, complete functions, reasonable structure, convenient operation, and good cleaning effect. It is of great significance for the cleaning of assembly line parts, improving the labor environment, and improving the cleaning quality. Its wide range of use is suitable for various manufacturing industries such as hardware parts, die castings, hydraulic components, gears, bearings, automotive components, and so on.

通過式噴淋清洗機工作前先檢查清洗液的配方濃度和配方比例是否合適，水箱液面高度是否夠；分別調定清洗液箱和漂洗液箱的電接點溫度計為50-60度；用鑰匙將電源控制開關，置于開位置；開啟加熱器，使其開始自動加溫；開啟浮油排除裝置開始浮油排除，因此式水泵未開啟，水面平靜，排油效果好。

Before working, check whether the formula concentration and proportion of the cleaning liquid are appropriate, and whether the liquid level in the water tank is high enough; Set the electric contact thermometer of the cleaning solution tank and the rinsing solution tank to 50-60 degrees respectively; Use the key to turn the power control switch to the ON position; Turn on the heater to start automatic heating; Start the oil slick removal device to remove the oil slick. Therefore, the water pump is not turned on, the water surface is calm, and the oil discharge effect is good.

等溫度升到預定值后即開始工作，操作者根據需要選擇開關，按每個單動按鈕，使水泵，吸霧，輸送等全部動作。當機器運行后，操作工人便可以在裝料口不斷地把零件裝載輸送網帶，清洗，漂洗，吹干，輸出，在卸料口取下清洗好的零件

After the temperature rises to a predetermined value, the operation starts. The operator selects the switch as needed, and presses each single action button to make the water pump, mist suction, and transportation all operate. After the machine is running, the operator can continuously load the parts onto the conveyor belt at the loading port, clean, rinse, blow dry, output, and remove the cleaned parts from the unloading port

通過式噴淋清洗機清洗工作結束后，當零件取下，按停止按鈕，全機停止。清洗液應定期添加自來水和一定比例的金屬清洗液以補充消耗，使液面保持在一定高度，如果清洗效果達不到工藝要求時，應全部更換清洗液。清理設備污垢后，關閉電源。

After the cleaning work of the through-type spray cleaning machine is completed, when the parts are removed, press the stop button to stop the entire machine. The cleaning fluid should be regularly added with tap water and a certain proportion of metal cleaning fluid to supplement consumption, keeping the liquid level at a certain level. If the cleaning effect does not meet the process requirements, all cleaning fluids should be replaced. After cleaning the dirt on the equipment, turn off the power supply.

此外在使用通過式噴淋清洗機中，我們要做好日常維護工作。按照正確的方法，做好一些維護工作，及時發現通過式噴淋清洗機設備的一些小問題，減少不必要的故障。

In addition, when using a through-type spray cleaning machine, we need to do a good job in daily maintenance. According to the correct method, do some maintenance work well, timely discover some small problems of the through-type spray cleaning machine equipment, and reduce unnecessary failures.

當通過式噴淋清洗機出現問題時，維修工作是非常必要的。當我們做這些通過式噴淋清洗機維護工作時，我們需要注意各個方面，這樣我們才能更好地完成整個通過式噴淋清洗機維護工作。

When there is a problem with the through-type spray cleaning machine, maintenance work is very necessary. When performing maintenance work on these through-type spray cleaning machines, we need to pay attention to various aspects, so that we can better complete the entire through-type spray cleaning machine maintenance work.

因此，在通過式噴淋清洗機設備的日常使用過程中，我們應該采取正確的方法認真做好這些日常維護工作，這樣通過式噴淋清洗機設備才能更好。更多相關內容就來我們網站http://m.nianyankeji.cn咨詢了解吧！

Therefore, in the daily use of through-type spray cleaning machine equipment, we should take the correct methods to carefully perform these daily maintenance tasks, so that through-type spray cleaning machine equipment can be better. For more relevant content, please visit our website http://m.nianyankeji.cn Consult and understand!